Winding VS Stacking – Which is Better for Lithium Battery?

With the large use of lithium batteries as power sources in mobile phones, digital products, notebook computers, drones, aircraft models, power tools, military, new energy vehicles, portable energy storage, medical equipment, etc., the domestic lithium battery industry has achieved rapid development. As an important part of the manufacture of lithium batteries, the stacking and winding technology has received extensive attention in the academic and commercial circles.

At present, China’s lithium battery manufacturers are mainly concentrated in the coastal areas of Guangdong Province. Among them, GREPOW battery is also one of the best, today we will share about the winding and stacking technology and its characteristics.

About stacking and winding

Winding technology: such as a cylindrical battery, the technology is to stack the raw materials in the order of the negative electrode, the separator, the positive electrode, and the separator, and directly roll into a cylindrical shape by a winding method, and then placed in a mWinding VS Stackingetal casing;

winding technology

Stacking technology: for example, a soft-clad battery, relying on a “stack”, such as a “z”-shaped stacking, first cutting the positive and negative materials into rectangular pieces of the same size, and then stacking them on the diaphragm, respectively. The Z” shape runs through it, separating the two poles, and finally wrapping the aluminum-plastic packaging;

Battery cell Stacking vs Winding Techonology

Winding technology Stacking technology

Internal resistance

Higher internal resistance Lower internal resistance
Normally, there is only a single tab for both the positive and negative electrodes. It is equivalent to a plurality of small pole pieces connected in parallel, which reduces the internal resistance.

Discharge rate

Low rate discharge capacity High rate discharge capacity
It is difficult for a single-pole to fully discharge at large currents. The multi-pole parallel connection makes it easier to discharge large currents in a short time.

Discharge platform

Low discharge platform High discharge platform
Due to the high internal polarization and high polarization, a part of the voltage is consumed in the internal polarization of the battery, so the discharge platform is slightly lower. The lower internal resistance is less polarized, so the discharge platform will be higher than the wound battery and closer to the material’s self-discharge platform.

Capacity density

Low capacity density High capacity density
Due to the thickness of the tabs, the circular shape on both sides of the cell, and the two layers of the closed film to occupy the thickness in vain, the internal space is not fully utilized, and the volume-specific capacity is thus slightly lower. The internal space of the battery is fully utilized, and thus the volumetric specific capacity is higher than that of the winding process.

Energy density

Low energy density High energy density
Due to the low volumetric capacity and the low discharge platform, the energy density is not as good as the stacking technology battery. The discharge platform and volume-specific capacity are higher than the winding technology battery, so the energy density is also relatively high.

Scope of application

Narrow application Wide range of application
For ultra-thin batteries, the thickness of the tabs takes up too much space and affects the battery capacity. Whether it’s an ultra-thin battery or an ultra-thick battery, the stacking technology can do the job.


Applicable to narrow thickness, the thickness is difficult to control Thickness is easy to control and not easy to deform
For the ultra-thin battery, the thickness of the tabs takes up too much space and affects the battery capacity. For ultra-thick batteries, not only the coils are too long to be controlled, but also the space on both sides of the battery cannot be fully utilized, and the battery capacity is also reduced. Moreover, the thickness is difficult to control. Because the internal structure of the cell is not uniform, the ends of the ear, the end of the diaphragm, and both sides of the cell are easy to be thick. The internal structure of the battery core is the same, and the thickness of each part of the battery is also consistent, so it is easy to control the thickness. At the same time, the internal structure is uniform and the reaction rate is relatively uniform, even if the thick cell is not easily deformed.

Battery shape

The battery has a single shape, is easily deformed, and can only be made into a conventional battery. Flexible size, suitable for high-rate batteries, shaped batteries, power batteries, etc.
Since the internal structure is not uniform, the degree of reaction inside the cell and the rate are not uniform during charging and discharging; therefore, for a thick wound battery, there is a possibility of deformation after charging or discharging at a large rate or after a plurality of cycles. Moreover, it can only be used to grow square batteries. Each pole piece size can be designed according to the size of the battery so that the battery can be made into any shape. such as the following:  Curved BatteryRound BatteriesTriangle BatteryHexagon BatteryUltra Narrow BatteryC Shape BatteryD Shape BatteryPolygonal Battery

The advantages of “stacking”

1. After working for a period of time, the positive and negative pole pieces will have a certain degree of expansion. The battery of the winding method is at the corner. Due to the different degrees of internal and external expansion, wave deformation will occur, which makes the internal structure of the battery unstable. In severe cases, breakage may occur, causing an accident;

Pouch Cell

2. The battery of the stacking piece, each layer will only expand up and down, the internal structure is still flat, and it is safer in comparison. In the safety tests such as vibration, extrusion, water immersion, and acupuncture, the battery exceeds the national standard. In addition, stacking method is because each of the positive and negative electrodes is isolated from each other so that each pole piece is provided with one tab and then welded together to form a final positive and negative electrode;

GREPOW stacking technology

3. But the winding method in order to reduce the process, only a few layers to install a polar ear, the total is usually only half of the former, however, the polar ear acts as a wire for the battery, because the stacking method has more polar ears, its The cross-section is also larger than the winding method, and the resistance is also reduced, so that the battery generates less heat during operation and is less prone to expansion.

4. Because of the rectangle battery currently used in electric vehicles, but the square-shell battery is bulky, the winding method will inevitably form a curvature at the four corners, creating a gap in the square shell, and the stacking method can make full use of the space, as much as possible With a square shell, the energy density will be about 5 percent higher than the former.

novel shaped battery

Is the battery cell made by stacking or winding better?

For consumer batteries, efficiency is increased compared to battery capacity and performance, so customers have a need for winding processes. However, for the power battery, considering the future of the battery is bigger and stronger, the industry generally believes that the stacking technology can give full play to the advantages of large-scale batteries, which have advantages over the winding in terms of safety, energy density, and process control. Therefore, for the field of power batteries, the stacking technology is an application trend of long-term development of soft pack batteries. At the same time, stacking technology can better control the cell yield, and the most important thing is to pursue high energy density, so stacking technology is the best choice in the future.

GREPOW novel battery

GREPOW’s decoding of key technologies for lithium battery stacking is the future for China’s lithium battery manufacturing industry.

Perhaps, the choice of no right or wrong, winding, and stacking is still determined by the market.

If you are interested in our products, please don’t hesitate to contact us at any time!
Grepow Website:

Winding and Stacking of Cells
lithium batteries

The performance of lithium batteries is closely related to its manufacturing process and equipment. This article will analyze the process Read more

Advantages of pouch cell battery, trend and opportunities
Pouch Cell Battery and Other types of battery cell

Generally, pouch battery can apply for every application, but why cylindrical, prismatic and other cells still exist? These types have Read more

How do Novel Battery Drive Innovation?

Today, everyone is tied to the high-speed train of technological progress. The introduction of new technology is almost always a Read more

Novel Battery to Innovative Medical Technology Design

Advances in technology are pushing manufacturers to create desirable products that achieve greater functionality, greater convenience, and faster results. This Read more

Share to

Leave a Reply

Your email address will not be published. Required fields are marked *